How to find your trailer's chassis number
A trailer's chassis number is what identifies it, like a hull number does for a boat. Trailers are stolen far more often than people expect, and most owners can't say what their number is. A boat trailer used only in the UK doesn't need to be registered with the DVLA, so there is often no paperwork to find the number in. If yours is stolen, the number on the trailer itself is what the police will want. It takes a few minutes to find.
1. Know which number you're looking for
The same number goes by several names: chassis number, serial number, VIN (vehicle identification number) or frame number. They all mean the number that belongs to your trailer.
You may also see an approval number, a model code, a weight rating, or a number on the coupling or the brakes. These are not the same thing. Some makers also cut a short "chassis code" into the drawbar. That identifies the type of trailer, not your particular one, so look for the longer, unique number.
If you've ever taken a trailer over 750 kg abroad, it will have needed a DVLA trailer registration number: one letter followed by seven digits, shown on a plate at the back. That is not the chassis number. The chassis number belongs to the trailer for good, and is on the plate and frame at the front.
2. Start at the front, on the drawbar
- Look for a small metal plate, or a sticker, on the drawbar or A-frame. This is the part that reaches forward to the towing hitch. It is the most usual place.
- Look on both sides. Many plates are on the right-hand side, but not all. On SBS trailers, for example, it is a yellow plate on the side of the chassis rail near the front, close to the hitch.
- The number may be stamped or engraved straight into the metal as well, or instead, usually on the drawbar or on the main frame near the front. Some makers, Indespension for one, put the full 17-character VIN on the plate and engrave it into the drawbar too. If you find both, check that they match.
- The plate often shows a weight rating as well as the number. Check you copy the chassis or serial number, not the weight.
- If it isn't on the drawbar, check the frame near the front, and the front or rear of the trailer. Small trailers without brakes sometimes have the plate somewhere else.
3. Newer and older trailers
- Newer trailers (roughly made in the last dozen years) often have a type-approval plate with a longer number of 17 letters and digits, which is the VIN. The last six or seven digits are usually the trailer's own serial number. Copy the whole VIN, not just the end.
- Older trailers and small unbraked ones often have a shorter chassis or serial number, or only a number stamped into the frame. Some have no number at all.
- A coupling or brake unit often carries its own plate, with its own number. That is for the part, not the trailer. If the plate is on the hitch rather than the frame, keep looking.
4. If you can't read it
- Wipe it clean. Road dirt, grease and salt build up on a trailer.
- A 17-character VIN never uses the letters I, O or Q. If a character in one looks like an O, it's a zero. Shorter, older numbers don't follow this rule.
- Photograph it with a torch held at an angle across the metal. Stamped numbers show up much better that way, and a photo is often easier to read than the real thing.
- Look under the bracket where a winch post, light board or mudguard is fitted. Plates are sometimes hidden behind them.
- Don't scrape or scratch it. A damaged number can cause problems later.
5. If there isn't one
- Check any papers you have: the receipt, the invoice or the handbook. A new trailer from a maker such as Indespension comes with a certificate of conformance that lists the VIN. Keep it safe, because you'll need it if you sell.
- Contact the maker or the dealer you bought it from. They sometimes keep a record by number, and can tell you where the number should be on your model.
- Don't invent one. A number that isn't on the trailer can't help anyone find it again.
- Photograph the trailer from the front, the side and the back, plus the make name and any distinguishing marks.
Still stuck? Get in touch and we'll help you work out what to do.
6. Write it down and take a photo
- Photograph the plate, close up and in focus, and take a wider shot of the trailer.
- Save the number, with the make, somewhere you can get at it from your phone, not only on the trailer.
- BoatID asks for the chassis number and a photo when you register a trailer, so they are kept with your boat and engine details.
- Tell your insurer, if they don't already have it.
If you're buying
The number on a second-hand trailer should match its paperwork and be clear and untouched. Ask the seller for the certificate of conformance too, if the trailer came with one. Trailer thieves are known to remove the plate and grind off the number on the drawbar, so if the plate is missing, has been removed or looks tampered with, or the numbers don't match each other or the paperwork, ask why. If the answer isn't convincing, walk away. Our guide to checking a boat before you buy it has more on this.
This is general guidance. The exact place varies by make, model and age, so check the maker's handbook if you have one.
Own a boat, engine or trailer?
Give it a BoatID of its own. It's free and takes about five minutes.
Register yours — freeBuying a trailer? Check a chassis number.